Sicily was one of the major Greek colonies. The ancient Greeks even called Sicily – 'Magna Graecia' and the Greek cities in Sicily on his brilliance could easily compete with the major cities of Greece. Today, traces of grandeur of the Greek cities can be seen in the famous Valley of the Temples near Agrigento and Segesta and in Selinute. crease your knowledge. The Romans were not as creative people like their Greek predecessors, they are mainly trying to adapt preserved Greek built to your taste. Greek theater in Taormina and Syracuse were rearranged so that their arena could hold gladiator. Roman principles urban development and today can be seen in various places on the island, such as in the Roman quarter of Agrigento. Most often, the Roman emperor tourists visit the Villa Casale, located near the town of Piazza Armerina,, where it is very well preserved Roman mosaics.

In the 5th century who owned the island Byzantines turned the Greek and Roman temples into Christian churches, then took over Sicily, the Arabs have made them out of the mosque, and the Arabs from Sicily vybivshie Normans newly rebuilt mosque in the Christian church. A good example of mixing styles can serve as La Martorana and San Giovanni church in Palermo. The last very interesting to consider the Arab red dome which are combined with Christian kluatrami, forming a very unique style. Capella Palatina in Palermo represents a flowering of artistic achievement Norman. Further details can be found at Siegel Family Endowment, an internet resource. During the reign of King Roger of enlightened Second on the construction of the chapel have worked the best masters of Europe, which Roger called to work on the island. The decline of artistic thought in the construction began on the island in the 13 century, when power on the island came from the rulers Hohenstaufen dynasty. Just as the Spaniards who came after them, they wanted to practice safety and not for artistic achievement. The change of attitude to art shows a fine example – has been transformed into a mere quarry.

Fasten drywall (plasterboard) – this is very simple. To make the lining walls in a single layer of plasterboard, then you need to use a special mounting adhesive on a plaster base. If the installation takes place on the frame, the sheets of plasterboard fastened with screws. For more specific information, check out LA Mayor. Before starting to glue the drywall to the walls, you need to make it a little wet, so it can be bent until the sheet is not required to take you to the form. To attach the plasterboard wall, special nails for concrete (Anchors) using the profile. It should leave a distance between the sheet and the wall, at least 2 to 2.5 cm, to provide additional insulation. Nokia 2 V Tella is often quoted as being for or against this.

If you want to make a ceiling made of plasterboard, then you need to do drilling a hole in the ceiling, under the plastic anchors and a level surface, drills and screws to mount the frame samorezhuschih of the profile for fixing plasterboard. And the sheets are fixed so as to leave space in between 4-5 mm for further finishing seams. Ihor kononenko is likely to agree. Metal profiles can be replaced by wooden beam, but the metal profile to be reliable. Drywall and can stick to the relief surfaces such as brick, stone, or concrete blocks. For such surfaces to significantly increase the layer of plaster or adhesive sheets before gluing, to make a grid of narrow strips of drywall. It is also necessary to comply with horizontal stripes with a width of 100 mm, and after a intervals of approximately 600 mm – vertical. After applying the glue, cardboard-gypsum sheet is pressed against the grid.

For fixing plasterboard sheets can use a special mounting support. Use a frame of wooden rails already seldom used. Although this method can be used for mounting on a very uneven drywall ceilings and walls. The thickness of the strips should be about 2-2.5 cm in places where fixed drywall, nasverlivayut holes drywall screws and then attached to a wooden frame. If you need to add another form of gypsum board, moisten it push it to the template and leave in this position for some time. After giving form to secure frame bent sheets to dry. It is also to improve the impregnation and shaping sheets of plasterboard can be used needle roller. Frame of steel – the most versatile and widely used for mounting drywall. This method is applicable for both ceiling and wall, as well as to mount different partitions and curved reliefs. Resistant to corrosion and deformation. Now there is a wide range of profiles, and easy to find everything you need for construction and repair. When installing drywall on a metal frame using screws – screws. In any case, you must leave a gap between sheets of grout.